Home > Hoods > Chevrolet Hoods > Chevrolet Corvette Hoods > Chevrolet Corvette Hoods 1997 - 2004 >

1997 - 2004 Chevrolet Corvette SuperCharger C5 RK5 Hood Carbon Fiber blister RK Sport 04011007CF

1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 Chevrolet Corvette SuperCharger C5 RK5 Hood Carbon Fiber blister RK Sport 04011007CF


 
Alternative Views:


Our Price: $1,880.68



Product Code: 1997-2004-CORVETTE-04011007CF


Make:


Model:


Year:


Qty:  
Description
 

This RK5 Hood was designed for use with the *Magnusen Supercharger which requires more clearance under the hood. Nothing says "Performance" like Carbon Fiber and this Supercharger hood features a deep, rich, hand laid carbon fiber center section. The fiberglass portion of the hood comes gel coated in gray and is ready for paint and prep. The carbon fiber blister is finished with a marine grade clear gel coat for protection and a high gloss shine. *WILL NOT fit the Magnuson 2.3 TVS 2300 Supercharger


If you want the fiberglass hood that is less expensive with no carbon fiber, please see product # 04011007 on our website or call/message us for help

Features
Extra Head-Room
Hand Laid, Hi-Temp Fiberglass Base
Deep Resin, Carbon Fiber Center Cowl
Installs utilizing Hardware from Stock Hood
Made with Pride in the USA


All RK Sport hoods use stock hardware for easy of installation.


Genuine RK Sport Hood! Made in the USA! By one of the very best!


Here at Brody Dog Auto, we do not sell cheap low end hoods! Or headaches you could call them! Over the years we have dealt with many manufactures & weeded out the bad ones. We have seen and heard it all. Nobody likes a headache & were not going to sell you one!

It is constructed from hand-laid fiberglass and high quality "ISO" resin.
Installs using stock hardware. Comes Gel Coated Gray ready to prep, prime and paint.
Made in USA Material: Fiberglass. Uses OEM hardware and Struts

Each hood comes with a one year warranty.

HOOD CONSTRUCTION:

Many of our ram air hoods are constructed of hand-laid fiberglass, using high quality "ISO resin" to give you the best possible quality in a fiberglass hood. It comes with a smooth gel-coat finish, on both top and underside surfaces.
All hinge and latch mountings are reinforced with steel plates. All bolt holes are pre-drilled and tapped for easy installation. To install these hoods, all you need to do is transfer your stock hardware onto it and bolt it on to the factory hinges for final alignment.
ISO resins are a higher quality, low shrink resin that allows the part to withstand more heat and prevent distortion.


SHIPPING INFORMATION:
-Hood Ships To All Lower 48 States
-ALL HOODS ARE BUILT AND SHIPPED TO ORDER
-Please allow approximately 30 business days before your hood ships (carbon fiber is very labor intensive)





Frequently Asked Questions

Q 1: Will water get into my intake with your ram air hood?
A. Our hoods have a built-in water management system to prevent water from getting in. To date, we have not had a complaint of water getting into an intake.

Q 2: What should I do if your product comes damaged?
A. Even though we package our products very well, occasionally the freight carrier will damage our product. In that case, refuse the shipment and do not sign for it. It is expressly recommended that the package be opened and inspected immediately upon receipt, even if the box looks undamaged.
CAUTION!!! If you sign off with the freight carrier on a damaged product, they will not honor any freight damage claim at a later date and you will be held responsible.

CAUTION!!! If you are having someone besides yourself receiving your package you must make it clear to them that they are not to sign off with the freight carrier until they have inspected the product and found it to be ok. If you have to refuse our product because it was damaged, simply call us and we will send you out another one ASAP. If you or someone else signs off on a damaged product, we will not be held responsible. You must refuse it!

Q 4: Should I prefit your products before I have them painted?
A. Yes, it is highly recommended that any hood be prefit before it is painted. This is especially true with fiberglass parts. If you are not the original owner it is possible that the vehicle was in a previous accident, which could effect how our product fits you vehicle. Even new vehicles are not all assembled exactly the same. Sometimes you have to readjust your fenders and do other minor adjustments to make everything right.

Features
  • Warning: CA Proposition 65 Message: WARNING: This product can expose you to chemicals which is known to the State of California to cause Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Share your knowledge of this product. Be the first to write a review »