Home > Hoods > Ford Hoods > Ford Mustang Hoods > Ford Mustang Hoods 2015 - 2017 >

2015 - 2017 Ford Mustang Ram Air Hood Functional with CARBON FIBER Rk Sport 18016110

2015, 2016, 2017 Ford Mustang Ram Air Hood Functional WITH CARBON FIBER Rk Sport 18016110 CUSTOM BUILT TO ORDER

Alternative Views:

Our Price: $1,452.50

Product Code: 2015-2017-RK-SPORT-18016110





Ford Mustang Ram Air Hood Functional W CARBON FIBER BLISTER 2015-2017 Rk Sport 18016110

This hood comes with the 100% real hand in-layed carbon fiber center scoop blister. You can paint the hood leaving the carbon fiber center for a complete custom look!

If you do not want the carbon fiber look, check out part # 18016100, on our website, for the hood without the carbon fiber that is less expensive.

All RK Sport hoods are hand laid fiberglass and use stock hardware for easy of installation.

Ram air hood with heat extractor vents for the 2015 - Up Ford Mustang.

Fully functional Ram Air Hood for the 2015 Mustang. The scoop will deliver cold air into your stock airbox for added performance. Heat extraction vents keep your engine running cool. This ships unpainted in a gray gelcoat ready for prep and paint (WITH THE CARBON FIBER CENTER BLISTER)

** Dealerships: We can ship additional hoods for no extra freight cost if shipped together.

Genuine RK Sport Hood! Made in the USA! By one of the very best!

Here at Brody Dog Auto, we do not sell cheap low end hoods! Or headaches you could call them! Over the years we have dealt with many manufactures & weeded out the bad ones. We have seen and heard it all. Nobody likes a headache & were not going to sell you one!

It is constructed from hand-laid fiberglass and high quality "ISO" resin. Has the hand laid carbon fiber blister
Installs using stock hardware and allows heat to extract through the vents. Comes Gel Coated Gray ready to prep, prime and paint.
Made in USA Material: Fiberglass. Uses OEM hardware and Struts

Each hood comes with a one year warranty.


Many of our ram air hoods are constructed of hand-laid fiberglass, using high quality "ISO resin" to give you the best possible quality in a fiberglass hood. It comes with a smooth gel-coat finish, on both top and underside surfaces.
All hinge and latch mountings are reinforced with steel plates. All bolt holes are pre-drilled and tapped for easy installation. To install these hoods, all you need to do is transfer your stock hardware onto it and bolt it on to the factory hinges for final alignment.
ISO resins are a higher quality, low shrink resin that allows the part to withstand more heat and prevent distortion.


- Hood Ships To All Lower 48 States
- Please allow approximately 4 weeks to ship your custom carbon fiber orders. They are hand built and shipped to order (very labor intensive).

Frequently Asked Questions
Q 1: Will water get into my intake with your ram air hood?
A. Our hoods have a built-in water management system to prevent water from getting in. To date, we have not had a complaint of water getting into an intake.

Q 2: What should I do if your product comes damaged?
A. Even though we package our products very well, occasionally the freight carrier will damage our product. In that case, refuse the shipment and do not sign for it. It is expressly recommended that the package be opened and inspected immediately upon receipt, even if the box looks undamaged.
CAUTION!!! If you sign off with the freight carrier on a damaged product, they will not honor any freight damage claim at a later date and you will be held responsible.

CAUTION!!! If you are having someone besides yourself receiving your package you must make it clear to them that they are not to sign off with the freight carrier until they have inspected the product and found it to be ok. If you have to refuse our product because it was damaged, simply call us and we will send you out another one ASAP. If you or someone else signs off on a damaged product, we will not be held responsible. You must refuse it!

Q 4: Should I prefit your products before I have them painted?
A. Yes, it is highly recommended that any hood be pre-fit before it is painted. This is especially true with fiberglass parts. If you are not the original owner it is possible that the vehicle was in a previous accident, which could effect how our product fits you vehicle. Even new vehicles are not all assembled exactly the same. Sometimes you have to readjust your fenders and do other minor adjustments to make everything right.

  • Warning: CA Proposition 65 Message: WARNING: This product can expose you to chemicals which is known to the State of California to cause Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Share your knowledge of this product. Be the first to write a review »